DELL EMC D-PEMX-DY-23 Practice Exams
Last updated on Apr 09,2025- Exam Code: D-PEMX-DY-23
- Exam Name: Dell PowerEdge MX Modular Deploy 2023 Exam
- Certification Provider: DELL EMC
- Latest update: Apr 09,2025
Which VLAN is reserved for internal switch communication?
- A . 1
- B . 3939
- C . 4001
- D . 4021
What automatically opens a support case with technical support and collects the PowerEdge MX system state information that is required for troubleshooting an issue, then sends it securely to Dell EMC?
- A . OpenManage Essentials
- B . SupportAssist Collections
- C . OpenManage Enterprise
- D . SupportAssist Enterprise
While servicing an MX7000 chassis a system administrator logs into OME-M and receives a Chassis Mismatch error.
What should be the next step taken by the administrator?
- A . Clear the configuration
- B . Reset Peer or the Local IOM
- C . Perform firmware update
- D . Force Active/Clear configuration
An MX7000 administrator has been tasked to create a Scalable Fabric Architecture on a 3 chassis setup using Fabric B.
Which IOM configuration is recommended?
- A . Chassis 1 C Slot B1: MX9116n; Slot B2: MX9116nChassis 2 C Slot B1: MX5108n; Slot B2: MX5108n
Chassis 3 C Slot B1: MX5108n; Slot B2: MX5108n - B . Chassis 1 C Slot B1: MX7116n; Slot B2: MX7116nChassis 2 C Slot B1: MX7116n; Slot B2: MX7116n
Chassis 3 C Slot B1: MX9116n; Slot B2: MX9116n - C . Chassis 1 C Slot B1: MX9116n; Slot B2: MX7116nChassis 2 C Slot B1: MX7116n; Slot B2: MX9116n
Chassis 3 C Slot B1: MX7116n; Slot B2: MX7116n - D . Chassis 1 C Slot B1: MX9116n; Slot B2: MX5108nChassis 2 C Slot B1: MX5108n; Slot B2: MX9116n
Chassis 3 C Slot B1: MX5108n; Slot B2: MX5108n
A system administrator must interface the compute sleds of an MX7000 chassis to a Z9432F-ON in a single SmartFabric.
Which FEM IOM is required?
- A . MX9116n
- B . MX5108n
- C . MX8116n
- D . MX7116n
A system administrator wants to disable Lockdown Mode.
Which interface should be used?
- A . iSM Interface
- B . iDRAC UI
- C . TPM Interface
- D . BIOS
Where are the diagnostic LEDs located on a PowerEdge MX750c compute sled?
- A . Front of the sled after removing the bottom two drives
- B . Middle of the system board with the top of the cover removed
- C . Located on the back of the sled
- D . Front of the sled after removing the top two drives
What is a characteristic of MX7000 networking in Full Switch Mode?
- A . Layer 2 bridging is disabled by default and interfaces must join a bridge domain (VLAN) before being able to forward frames.
- B . Networking is enabled by default and all switch-specific OS10EE capabilities are available.
- C . Networking is available on MX9116n FSE and MX7116n FEM but not on the MX5108n.
- D . Switches operate as layer 2 I/O aggregation devices and are managed through OME-M.
Which statement describes L2 Multicast as implemented on the PowerEdge MX7000 IOM?
- A . MLD snooping and IGMP control or limit the flooding of IPv6 multicast traffic on VLANs.
- B . MLD snooping and IGMP control or limit the flooding of IPv4 multicast traffic on VLANs.
- C . MLD snooping controls the flooding of IPv6 multicast traffic on VLANs while the IGMP limits the flooding of IPv4 multicast traffic.
- D . MLD snooping controls the flooding of IPv4 multicast traffic on VLANs while the IGMP limits the flooding of IPv6 multicast traffic.
An administrator is about to perform a firmware update on an MX9116n switch OS 10 from the CLI. The latest OS 10 switch firmware image has been downloaded and their TFTP server is set up. Upon logged in with administrator credentials on the switch, which command should be used to start the update procedure?
- A . firmwaredownload tftp://server-ip/imagename
- B . install tftp://server-ip/imagename
- C . fwupdate tftp://server-ip/imagename
- D . upgrade tftp://server-ip/imagename